Tactical Grip Tape 46 Pre Cut Hexagons Textured Stickers Black

This textured tape is exactly like talon rubber grips. I put talons on my grip handle and ordered these for indexing spots and you can't tell the difference which is which brand. Adhesive seems strong and in and out of the holster hundreds of times has not peeled yet.

I bought this to improve the grip on my new BLU Life One X2 (excellent phone). The phone has a slim metal case, incredibly card to pull out of your pocket and hold comfortably in normal use and in gaming. When I felt the HEXMAG grip for the first time, I was not convinced it would do the job, but after carefully applying to the phone, all I can say its WOW. They work unbelievably well. My grip on the phone is secure, and with the pattern I've put on it, it works well in gaming position and looks cool. The only downside is the dots may get dust pickup around the edges. I also went through a lot of them doing one phone case. I recommend buying two packs and you'll be able to use these in other places, like your Amazon Fire stick remote. Since these are intended for automatic rifle magazines, there's the added bonus of my purchasing these may keep them off the magazine of a mentally ill person's AR15 and I could be saving lives.

First, the Hexmag grip tape comes in a small sheet, and is pre-cut. The grip aspect of the tape is somewhat coarse, nowhere near as rough as skateboard grip tape or sandpaper though. I carried my ar around all day at the range and didn't notice the grip tape being too rough or rubbing my hands raw. Additionally, the grip surface doesn't seem to catch or cling to articles of clothing or gloves. One might have an issue with hands sweating and loss of grip, but I cannot speak to that as of yet.The grip tape seems to hold on polymer surfaces. I did not try to attach to anything other than plastic/ polymer. I attached the grip tape to the Hexmag grip and the Magpul handguard on my ar. I didn't bother to clean the surfaces with anything but a dry cloth and simply pressed the pre-cut pieces where I wanted them. Then I applied firm pressure for around 3 seconds. Next, I used a lighter to try and slightly melt/ heat up the piece to make it less stiff and more gummy. I've read other reviews mentioning a hair dryer to secure the tape; I found holding a flame a few inches below the tape will help suck the oxygen out. Apply more pressure and let harden, worked for me. I did try to get creative with small, thin strips of leftover material and most would not hold, or they would slide across the polymer. Stick with the pre-cut pieces and the larger border pieces.This review is too soon to adequately know if the grip tape will hold, only time will tell. I will try and edit my review if the tape falls off or creates negative aspects.

5-star for the grip kit. No stars for Hexmags. Sorry. Loved the design, cool bling factor, but I have a warning for you Hexmag users. And let me say I REALLY wanted to like Hexmags. I am a 28 police officer. 24 of those also as a firearms instructor. I am a Glock Armorer and an AR-15, M16 armorer. Can’t recall the exact date but the latter part of 2015 I purchased several Hexmags. I went to a day of rifle training and qualification. All my new (brand new just opened that morning) Hexmags performed flawlessly all day during training. Right up until qualification. Under the stress of the qual and time constraints, I performed a speed reload (rifle empty, bolt locked back, inserted a loaded mag). Under that little bit of stress I inserted the fresh mag and it went TOO far into the magwell (DPMS) and locked up the bolt. I had to hold the rifle, depress the mag release, and the instructor had to forcefully remove the mag. Needless to say if that small amount of stress caused me to over-insert the magazine, imagine if I were being shot at and had to reload. I was fortunate the company I had purchased them through allowed me to return them for a refund. Here is a cut and paste of Hexmag’s response:“Good afternoon Detective,Thank you for taking the time to contact us about this issue that you had with our magazines. We are very sorry that you experienced this. I can assure you that this is not a chronic issue with our products, we have only had 2 reports of over insertion and this is the second. Our products are used daily in high stress situations by all of our sponsored 3 gun competitors, several of whom are active Law Enforcement.The first issue we physically witnessed was when we sponsored a range at the Colorado Law Enforcement Firearms Instructors Association. One of the instructors was a rather large gentlemen that was physically able to over insert one of our new FDE magazines under a high stress situation. Using that same over inserted magazine we physically could not reproduce the issue without damaging his rifle. We replaced his magazine and he completed all the training.In order for our magazines to work along with Pmags and GI mags the magazine catch pockets must be a specific size and in a specific location. We cannot add an over insertion stop to our magazines like Magpul did with their Gen3 mags, it causes too many fitment issues with too many rifles; mainly any rifle with a flared magazine well will not work with a Gen 3 Pmag.We are glad that one of our top dealers Tactical Link has superb customer service and they were able to refund you for the magazines. If you are ever willing to try our products again please contact us. We would be more than happy to send you some of our latest products free of charge.”

Got these to put on my iPhone XS case. I have a small hand (female 5’) and I’m clumsy so I am prone to dropping my phone. Because of that, I can’t use the sleek and slim cases. Even the ones that are supposed to be anti-slip are still too slippery. I end up having to have a slightly wider case that has more of an edge around the case, but having such a small hand, even 0.5 mm wider makes a difference. I wanted to switch to a slimmer case to make it easier to hold but couldn’t find any with enough grip for me. Came across a pic of someone using these on the phone and so far, these are excellent! I’m not creative so I didn’t do a pretty pattern on my phone but these make such a huge difference. I can actually hold my hand almost completely sideways with my fingers barely curled around the edge of the bottom of the phone and it doesn’t fall out of my hand!!! I hope these hold up well but considering they’re for gun magazines, etc; I’m guessing they will!