CHUMXINY Brake Bleed Kit for Shimano,TEKTRO, MAGURA Range of Hydraulic Disc Brakes, Including High Performance Mineral Brake Fluid (120ml).

Cheap and comes with all the pieces you need. Firstly, it comes with all bet bits you need to bleed the braked on Shimano Ultegra R8000 Road Brakes. You do not need to buy the Shimano adaptor. I will share an idiots guide below in case anyone needs it. 1) Slide the brass retainer over the clear tube and push the end over the syringe. The brass ring is to hold it tight. 2) Remove the wheel, retaining pin and screw to remove the brake pads. 3) Fit the yellow brake pad in the void and re-apply the retaining screw (If the yellow block won’t fit, use something to push the pistons back then apply again). 4) Slide the tube clamp over the tube 5) Attach the hose and syringe to the bleed valve, using the 7mm spanner (included), open the bleed valve, literally 1/2 a turn. 6) Close the tube clamp and go to the lever. 7) Peel the hood back, expose the screw. 8) Using a 2mm Allen key, remove the screw and keep safe. 9) Find the yellow adaptor to fit the hole, try the larger ones first. 10) Attach the yellow funnel and 1/2 fill with oil. 11) Release the tube clamp and draw the fluid back into the syringe until there are no bubbles (you will see the fluid being drawn out of the funnel) 12) Close the bleed valve on the calliper then pump the brake lever a few times, you may see some bubbles, but until it feels firm. (Took me about 6 pumps then it was solid) 13) Push the plunger into the funnel to stop oil leaking out when you remove the assembly. 14) Carefully unscrew the yellow Cullen and adaptor, when removed re-apply the brake lever screw and tighten. 15) Clean the area of oil, isopropyl alcohol works well, or just wipe with a tissue and put the hood back. 16) Clamp the hose at the syringe, carefully remove and immediately wipe the area clean. 15) Re-assemble the brake pads and wheel etc, and enjoy your new brakes. I cannot fault this system. I am a 1st time brake bleeder. It took 5 minutes, worked flawlessly. You don’t need any other kit, or to pay your shop £25 to do it for you.

All you need to bleed and restore your hydraulic disc brakes on your bike/s. Worked fine on my mid price Shimano sets. Would imagine that the additional parts and adaptors would work with most other popular brands (but best to check). If you’re new to doing this, consider checking out a YouTube clip first and rehearsing the process beforehand. Straightforward really, but easy to goof up (embarrassed to admit I mistook a fixing bolt for a bleed valve in my rush..) Enough in this kit for several bleeds. Stopping power restored!

For many years, until 2007, I was a professional bike mechanic - working in a shop and also with professional race teams. Long story short - things have changed. My 'old' bleed kits no longer fit all of the brakes and often now they don't have an open reservoir at the top - requiring two adapters and syringes - or a 'makeshift' (little pot) reservoir. I was asked to bleed some Magura MT2's (which had no top reservoir). This did the job just fine. Granted my expensive professional kits are better quality but they wouldn't do the job here. This did what was required. Good points - multiple fitments, dual syringes, sufficient mineral oil, little case and good price. Not so good points - the plastic adapters are not as good quality as the metal in the pro kits (read Magura, Shimano etc) but are adequate. As I am no longer bleeding multiple brakes each day - this will probably last me until my time is up. Based on that - 4 stars. If like me you get asked to bleed all kind of brakes this is just the job. If you are only occasionally going to be doing your own - pro kits are better quality (I just didn't want to buy 4).

Got a bike recently with hydraulic brakes, and the front brakes were binding. I looked online and tried to figure out how to re-align them, but unfortunately I managed to undo the wrong bolts and squirted out some of the hydraulic fluid. Using this kit I was able to connect up a syringe and funnel at either ends, and with a bit of pumping of the brake lever, was able to put the fluid I had removed back in. There were loads of connectors in the kit, so took a little bit of trial an error to match up to my bike, but once done I was able to solve my issue and get working brakes again. I've no idea about the quality of the brake fluid, but after a few rides I am pretty happy with the kit.

Very pleased, it had everything I needed to bleed my SLX brakes, including a little flat spanner for the bleed nut which was useful. Process was almost as identical and simple as shown on the video barring a few minor details; it doesn't tell you to remove the brake pads and insert the provided block spacers (probably obvious but nearly caught me out) and also it shows drawing 20ml of oil out of the bottle after already pouring 20ml into the system is impossible because the hose isnt long enough and I had to open the other bottle. I'd say it took me over an hour but I was being pretty meticulous following the video to the letter, I think you could get quick at it with practice. Brakes are now very consistent and positive but didn't solve the large amount you have to pull the rear brakes to bite (I guess that's just a fault with mine). Note that the syringes are marked single use only (I don't see why with a good clean?) But there's two of everything, I think you could do both brakes twice with what's supplied and then just buy more mineral oil unless there's a really good reason the plastic is single use.

Worked on my Clarke brakes no problem. I did have to loosen/extend the lever on my handlebars for it to work (which was not shown in online guides)

Overall the kit was fine, the barbed connector for my tektro hydraulic brakes didnt have long enough thread with the o-ring in place, managed to get the job done with a little fiddling though

Normal quality

Worked flawlessly for my tektro brakes, very easy to use and took very little time.

Excellent produit, fournis avec tous les adaptateur et huile de qualité, merci.

Hat bei mehreren Rädern mit Shimano Bremssystemen sehr gut funktioniert. Es ist alles dabei was man braucht.

It arrived in less than 19 hours (thanks to Prime). It has a nice box with everything you would need, including gloves and two pairs of syringes and tubes, and it comes with a small wrench suitable for the bolt on the end of the brake cable. The hex key provided was a bit big for the screw on my brake lever (which was not a big deal). Finally, the manual provided (in multiple languages) is very clear, and covers important notes that I hadn't come across in YouTube tutorials I had watched. With it I could fix my bike quite easily and I am very happy with it!

J'ai récemment acquis le kit de purge de frein CHUMXINY pour les systèmes de freinage hydrauliques, et je suis extrêmement satisfait de son efficacité et de sa facilité d'utilisation. L'un des points forts de ce kit est sa polyvalence. Il est livré avec des adaptateurs pour s'adapter à une large gamme de systèmes de freinage hydrauliques, ce qui le rend parfait pour les amateurs qui ont différents types de vélos à entretenir. La procédure de purge elle-même est simple et intuitive, même pour les débutants. Les instructions fournies sont claires et faciles à suivre. J'ai réussi à purger mes freins sans aucun problème. En conclusion, je recommande vivement le kit de purge de frein à tous ceux qui cherchent à entretenir leurs freins hydrauliques. Sa qualité, sa facilité d'utilisation et sa polyvalence en font un investissement judicieux pour tout amateur de vélo soucieux de l'entretient de son vélo.