MasterCase H500P Mesh

Before I built my current computer, I used CoolerMaster's HAF X case and I was looking for a comparable case. I was always happy with the HAF X, but it was time to move on to something new for the new build. I did a lot of research on cases, knowing I wanted to stay with CoolerMaster. The H500P came up on a lot of review sites and had negative reviews, due to the plastic part at the front restricting airflow. The H500M had much better reviews, but was twice the price. Then I saw this case, the H500, which was a good combination of airflow (thanks to the mesh, although it does come with an optional plastic panel as well) and price. I usually prefer full tower cases so I have lots of room to work, but this case was roomy enough for me to get everything I needed in without too much discomfort. The case comes with 2 RGB front fans and fan controller, which I used to set mine to green, as shown in the first photo. I must put a disclaimer, though, that the case DOES NOT come with 2 top fans or the light strip as seen in the second photo. I ordered and installed those separately. The top part of the case has a magnetic dust filter which is easily removed and cleaned. The bottom part of the case has a dust filter for the PSU that can be easily removed and cleaned as well. The glass side panel makes for a nice view at the components. Overall, I'm really happy with this purchase and would recommend this case to anyone looking to build a new PC. PS: As a side note, I have to add that I was looking up whether a Noctua NH-D15 would fit in this case, but found no reviews on any site that would help me, so I thought I'd post it here. CoolerMaster says the CPU cooler clearing is 167mm and Noctua says their cooler is 165mm with both fans attached. 2mm is not a lot of space to gamble on, but I took the risk and can safely say that mine fits like a glove. The Noctua does not touch the glass side panel of the case whatsoever. If you're looking into doing this type of setup, make SURE you have the Noctua's fans mounted as close to the motherboard as you can without touching any components (RAM, etc.). Any higher and they WILL touch the glass panel, so adjust them as needed until it fits correctly.

I have wanted this case since it released :D The second I saw it, I knew I wanted it in my dream build! The amazing ventilation and the variety of water cooling support it gives if you wanna go down that route is really generous. Since I'm not doing water cooling, it meant I had room to personalize the interior with a few lego figures The opportunity to swap out the front mesh for glass is really nice, I'm gonna keep it mesh myself as I prefer airflow and there are still three glass windows on the sides and top which gives your system the chance to be pretty and eye-catching! The only drawback is baring finger-prints in mind Harddrive space is really generous too, given how more and more people are moving to SSDs over mechanicals. It makes sense for only 2 HDD slots but 7 SSD mounts, hell you could even use one of them for any third-party RGB devices (which I intend to do!) I also wanna say that there is plenty of room in the case for cable tidy providing you know what you're doing. As someone who has never built in a full-size case like this, it was a new challenge but one I was very happy to take on! So with all that in mind, I am gonna wrap this review and just say that this case is amazing. Worth the money! Definitely is the best version of this case from CoolerMaster, I know they released two prior versions which are nice but for me, this one is so sleek, fun to build in, looks sexy and just has the right balance to between function and form! 10/10!

This case was my first build and it really helped. Great for cable management, although a tad tight at the back but plenty of options for cable routing. Brilliant selection of mounts, power shroud good. Loads of screws, velcro and normal ties included. The flexibility is awesome as you can mount radiators top or front, will take all sizes. I just mounted 240mm radiator CPU water cooler to front fans and the 2x120mm to top (from water cooler). Front RGB fans are great and sync with MB. Easy to plug in once you suss out the cables from the case (took me a while!). Good selection of ports (2xUSB 3.0, 2x2.0 etc). It runs fantastically cool and quiet. Major airflow (don't use the plastic panel!) and looks great. It's also easy to carry due to handle at the top on the front end. The full window smoked panel is perfect for viewing. For the price I found this the best option, and I did look at a lot of cases!

Great build quality, good balance between minimalism and with a bit of RGB. I love the two big front fans. Found the instructions very difficult to follow at times as to wiring of fans/rgb. Easy cable management with good access points. Brilliant airflow options.

Purchased as a replacement case for an existing i7 build to improve airflow and future proof for a planned upgrade later in the year. Moving the existing components into the case was an easy process, and there is plenty of space to work in and to get a nice tidy finish. Noise levels are fine with the 200mm fans and a tower air cooler on the CPU. If you are replacing an existing PC/case just check the overall dimensions as it's on the larger side compared to a lot of old pre-built systems, make sure it will fit where you plan to put it! The mesh front is working well to keep dust and pet hair out and is easy to clean off as it's flat and there are no bars or fancy details to get in the way. Very pleased with this and would recommend. Just need more RGB to go inside when I do the upgrade later in the year.

Ich war für meinen neuen PC auf der Suche nach einem Gehäuse das ordentlich Platz bietet, ohne dabei zu protzig zu wirken. Viele Gehäuse versuchen mehr zu sein als sie sind und lassen einen das auch am Preis spüren. 200€ fand ich für ein Gehäuse dieser Grösse und Ausstattung allerdings vollkommen angemessen. Es kam wesentlich früher als angekündigt was mich natürlich gefreut hat. Beim auspacken merkt man direkt, dass man sich Gedanken gemacht hat; wer schon mal alleine ein Gehäuse aus dem Karton geholt hat, weiss wie schwer das sein kann. Besonders dann, wenn das Gehäuse so viel wiegt wie das Cooler Master H500M. Als Lösung wurde das Gehäuse samt Umverpackung in eine Tasche gesteckt, so dass man es auch alleine wunderbar einfach aus dem Karton holen kann. Das Gehäuse selbst ist wirklich massig und durch die rundum-Verglasung sieht es extrem edel aus. Das Frontpanel bietet mehr als genug Anschlussmöglichkeiten und wirkt wie der Rest sehr hochwertig. Das Innenleben ist gut durchdacht: die Kanäle bieten genug Platz für alle nötigen Kabel und dank der abnehmbaren Blenden sieht sogar die Rückseite wirklich ansprechend aus, was meiner Erfahrung nach recht ungewöhnlich ist. An einer dieser Blenden wurde der RGB-Controller angebracht. Die Lüfter sind bereits damit verbunden und man muss man das ganze nur an Mainboard und Netzteil anschliessen. Die Farben der Lüfter können dann über einen kleinen Knopf am Frontpanel durchgeschaltet werden, dafür verzichtet das Gehäuse standardmässig auf einen Resetbutton. Wenn man ein Board mit entsprechender RGB-Unterstützung (z.B. Asus Aura) verbaut hat, kann man den Schalter aber auch einfach ans Mainboard anschliessen um einen Resetbutton daraus zu machen. Wie in der Beschreibung zu lesen ist, hat man die Wahl zwischen zwei Fronten: gehärtetes Glas oder einem Mesh. Was nicht in der Beschreibung steht, ist dass das Mesh noch ein zweites, kleineres Gitter im innern hat, was möglicher Weise als Staubfilter fungieren könnte. Ob das wirklich was bringt, kann ich aktuell noch nicht sagen. Ich hab mir zur Vorsicht noch extra Staubfilter dazu bestellt. Ich habe weder eine Wasserkühlung, noch zusätzliche Lüfter verbaut. Trotzdem reicht der Luftstrom der beiden 200mm Lüfter aus, um meine Hardware (Ryzen 7 3800x, RTX 2070 Super, NVME M.2 ohne eigene Kühlung) auch unter Vollast kühl zu halten. Eigentlich hätte ich noch einen Stern abziehen müssen, da der Anschluss der Audiobuchsen bei mir ein loses Kabel hat und dementsprechend nicht funktioniert. Ich habe nicht vor die Buchsen zu nutzen und weiss mit Sicherheit, dass das Gehäuse ohne Probleme ausgetauscht worden wäre, ich wollte aber nicht noch länger mit dem Zusammenbau warten müssen. Ich bin vollends begeistert und würde das Gehäuse uneingeschränkt empfehlen.

بعد سنة من الاستخدام اقدر اقول انه افضل كيس ممكن تاخذه صحيح السعر عالي بس المميزات الي فيها وحجمه الي يدعم كل القطع يخليك ماتستخسر فيه عيبه مافيه خيارات كثيرة لاماكن الامراوح محدودة جدًا

It's a great case , a perfect cabinet for gaming and for content creator .it's a cooling beast. But unfortunately I had to exchange it because I received defective product from seller tps tech. And when I received it for second time it was completely different cabinet it was fake so I had to cancel the order and returned it back. But again the case is awesome, go with it eyes closed . It will cool down your system very well. Even bettthan lian li 215 or other more expensive cabinets.

No se dejen llevar por el titulo es grande solo que aparenta ser mas grande de lo que es, en mi caso instale un custom watercool para cpu y gpu y apenas logre que entrara PERO por que las piezas son grandes en mi caso es un radiador de 360mm con el doble de grosor de un radiador normal y un combo de bomba y deposito grande e thermaltake el mas grande que tienen, por eso para mi fue posible pero problemático de instalar todo pero para instalaciones mas comunes es perfecto y es hermoso el vidrio templado es exacto para dejar pasar el rgb de manera hermosa y dar una imagen mas oscura al estar apagado sinceramente NO PUEDES ARREPENTIRTE DE COMPRARLO.

melhor gabinete que tive até hoje