SkyGuard Shed Roof Kit - EPDM Rubber Roofing Kit for Sheds & Outbuildings - Longer Lasting Alternative to Roofing Felt for Sheds (1.4m x 1.1m)

Smashing stuff, plenty of glue with some to spare, so no need to skimp. Easy to work with, nice and thickness is just right. Watch the video to see how to apply the glue. I did my back porch area on a dry day, but not too much sun, as I didn't want to glue to go off before I was ready for the next section. I lipped the edge up on the sides and folded in the corners, as this was not a shed roof. I appled the glue to about 600mm depth of the roof and smoothed it down with a paint roller, being sure to push any air pockets out, I did the same size again, until I was lapping in to the gutter. It has rained heavy since and not a spot of water has got past it, I did add some side strips to cover over the lipping, as the sides were on to a garage and conservatory. I have posted a couple of pics. Well worth the cost, and a little of your time. I made sure to vac any dust from the before I started. Not one air bubble, don't forget to use a paint roller with some pressure, to be sure you get a nice bond with no air bubbles. Good luck and enjoy your new roof. I will do my workshop roof next year.

The kit turned up on time and contents were as expected: Exactly 3.0m x 3.5m rubber sheet circa 1.0mm thickness. Two tubs of glue and a mini-roller. Disposable plastic gloves. A tube of sky guard mastic. After reading some online information, I decided to replace the polycarbonate sheets with plywood sheets as product is described as for bonding to wood. Laying out the rubber sheet on the roof revealed how exact the measurements were. Thankfully 25mm on either side for the conservatory is sufficient to drop into the drainage channels, it was a bit close! I ignored the mini-roller as it was ridiculously undersized for the area I am doing. Made use of an old large paint roller I have. Having spent time brushing the sheet flat and letting it relax as much as possible I applied the glue. There is sufficient for the area, with little to spare. I have some left over as I have an overhang of 0.3m x 3.5m which requires zero glue. Otherwise I think like others there would be an exact amount of glue. Minimal wastage is good for the environment. Brushed out air bubbles as best as I could, and it is hard to do on an area this size by yourself. Having to accept it is not perfect. The glue changes colour from white to a luminous violet in the sunshine and if you get it your hands it becomes impossible to handle anything as the tackiness starts to kick in. Recommend a decent throw away pair or two of disposable gloves. I did not use the thin plastic one which are supplied. The bulk of the job was done in a day, having to resort to use of ‘flashband’ product, purchase separately , at the point where the rubber meets the wall to achieve a waterproof seal. I find the product is easy to use, apply and relatively quick to fit compared to traditional felt roof product and it should last 40-50years. Superb stuff. Just measure twice before buying. Keep the leftover rubber and use it for other tasks. I have found several uses for it over the years, mainly hose pipe washers, tap washers, weather strips, draft excluder. After a recent severe storm of high winds and rain, there are zero leaks, no drips and no trickles of water on the inside of conservatory as there was once before. Job Done. Well Happy. 😃

Good quality rubber, thick enough and strong. Plenty of adhesive provided, and plenty of edge sealant. All arrived in a nice kit with everything required. 10x6 shed completely re-roofed in 4 hours including an hour for the rubber to rest. Great value if it lasts as it should - the 'premium' felt only lasted 3 years!

Product was excellent and simple to use, although I would advise doing it with two people for larger areas. However instructions were limited, so I strongly recommend looking up the YouTube references to watch online instructions as this is very clear.

Very good kit easy to use great Finnish , no extra adhesive needed

Much easier than felt to fit and looks better as its one piece. Easy to cut and fairly easy to remove bubbles. Instructions supplied for a pent roof but it's a little different for a single slope. We used a long piece of timber to stretch and anchor, working downwards. Wrapping it first to keep it tight and positioned for the adhesive.

Used for roofing my new summerhouse. Follow the instructions and it's easy to fit, all you need is included in the kit. Feels to be good quality material, time will tell.

First off, I'm not an experienced DIY'er but I do like to "have a go" if I think a job's within my (limited) capabilities. I've not refelted a shed roof before so this whole experience was a first for me. My shed roof is roughly 11 ft x 12 ft. The SkyGuard membrane came as a single piece with two joins; the joined parts were all the same shade. (A nitpick of some other reviewers was that the constituent sections were different shades of grey.) The kit came with no instructions whatsoever, but it was easy enough to google around and find videos and the like explaining the installation process in detail. I found the membrane dead easy to work with (working on my own as I was), and I had it glued down to the roof timbers very quickly. I didn't bother to buy separate edge trims (available from some other suppliers); instead I simply used the sealant provided, which seems to work fine. In all, I have a high level of confidence that this roof covering is watertight and that it will last a long time - long enough for me to never have to recover the roof again during my lifetime. It's more expensive than felt, but well worth it in my opinion if it lasts as well as expected. I'll post an update in 50 years.