TORCHSTAR LED Safe Lighting Kit, (4) 12 Inch Linkable Light Bars + Rocker Switch + UL Power Adapter, 600LM, Input 100-240V, for Under Cabinet Gun Safe Locker Closet Showcase, 5000K Daylight

The countertops in the kitchen are dark when I try to work at them because my body blocks the light from the center of the room. I had installed one of the fluorescent under the cabinet lights. It was OK, but was only about a foot long so it only lit up a small area. I liked it pretty well so I was planning on just buying 3 more of the same one so that it would get the entire counter top. Then I realized that each one would take up an outlet. Since I have a lot of countertop appliances, I really don't have 4 outlets to spare. Luckily, I came across this one, which was a great price and since I would be buying just one instead of 3 more, that made it much better.It has far exceeded my expectations. I blinded my husband when I first turned it on because he was looking right at it. It is very bright. Much brighter than the fluorescent one I had previously. It is essentially 4 strips on one outlet with one switch. We used all of them along the underside of the cabinets along one wall. If my cabinets had been shorter, I could have used fewer of them, or used 2 under one cabinet since the wires between the strips are flexible. I really like that I have multiple options for configuration. I assume that we can even add more to them and still run them off of the one wall plug because of the way each piece plugs into the others. I don't need more on that side, so I haven't looked.Each of the light strips has a strip of double sided tape attached down the entire length and also a hole on each end if you would rather screw them to the cabinets. We just used the tape for now but since I have a toaster and a coffee maker under them, I'm not sure if the sticky tape will hold up to the heat and moisture. If they fall, we'll just screw them in. They are very light weight so if they do fall, I don't worry about them damaging anything. I think the previous light weighed a couple of pounds so we had to screw it to the cabinets. I like it when products give you options like that.My husband did find one "problem" that is not a big deal and may be due to something he did wrong but I'm not sure. He was going to screw them in at first and found that the double sided tape on the back keeps the tab with the hole from sitting against the cabinet so when he tried to screw it in, the tab broke off. He thought maybe he needs to take the tape off so it will be flat. I would just use a small rubber washer/spacer between the tab and the cabinet.Since they are LED, they should last a very long time. I have read that LED lights last thousands of hours, but I don't have enough experience to say if that is true or not. They are cost effective enough that if they even last a couple of years, they will have easily earned their keep.

Not a bad price for these lights, very bright and easy to install, does come with the Velcro tape if you have some carpet in your safe but overall these lights are worth it

I've ordered these lights a couple of times for different applications. They are a great product. Both the 3000k and 5000k. The 5000k does not have that blue tint to it. It's a clean white light. The 3000k has a clean warm incandescent look. Zero problems with the lights and the connections and 12in light assembly are well made.

I purchased the motion sensor system since I did not want to be switching the lights on/off constantly. I had recently mounted a microwave above the stove & used that power outlet which was within the cabinet, so no ugly dangling cords. I drilled thru the adjoining corner cupboard for the power cord, and then thru the base of the same cupboard. The lights have good 3M mounting tape to mount them under the cabinets, the lights come with no screws anyway, the only slight problem I had was where to mount the motion sensor as the wiring is only about a foot long, I used Gorilla glue to mount it to the base and facing outwards on the cabinet, its out of the way, not a good place but its ok. The excess cord I rolled up and used duck tape to secure it under the cabinet. Not pretty yet, but who bends down to look under your cabinets anyway? right?. So, all in all the system is ok, I used the system on three corner cabinets, works very well and it lights up a otherwise dark corner, the wife loves it and that's the main point, , of course I have a spare light strip, could not use that.

I installed these under-cabinet lights in two places in our kitchen and was very pleased with both the ease of installation and the resulting light. The LED strips are thin and tuck away nicely under the front lip of the cabinets, out of sight until you need them. The strips shine at a 45 degree angle, so they provide good illumination on both the counter and the backsplash. They provide uniform, good color-balanced lighting, not too bright or too cool. The 3M self-adhesive is very strong and securely fastens the strips. I used "EShine Extension Cable - Male to Female - for LED Under Cabinet Lighting..." to extend the light strips to reach another section of cabinet and still use a single power plug and on/off switch. The self-adhesive wire clips provided with the extension cable were very helpful in supporting and hiding the wiring. My suggestions to Torchstar would be to include some of these clips with the LED kit.

These lights are very easy to install with pre attached double sided adhesive tape or the cast-in screw holes if you prefer. I had these installed in 5 mins. The cord is super long which depending on you application could be good or in my case it is just excess wires you have to tidy up. I just bundled them up and stapled them under the cabinet and unites you look under there you'd never know. Overall, they're bright with a nice warm color and create zero heat which is nice if you have them under cabinets storing food. They do use one of your outlets, but I just upgraded to a 6 outlet setup and is no longer a problem. I've had one set up about 6 months no issues and this ones been up about a week now. I'll update if I have any negative issues.

Lo mejor para iluminar tu colección de figuras

Pleased with how well these lights are made. Tons of light, everything is a twist lock design for the connections. The lights themselves have 3M adhesive on two sides for installation, or you can use screws with the brackets on the ends. The case they're in is all plastic with a clear plastic lens. The switch is a rocker type switch with adhesive on the back as well. Maybe the only thing that could be improved is the length of the power adaptor cable, which is approx 3'. Great lights!