BIQU Designer Smooth PEO+Smooth PET Double Sided Build Plate for Bambu-Lab H2D/H2S 3D Printers 346x355mm Spring Steel Flexible Sheet Removable Surface Platform

After using this build plate almost exclusively for over 2 weeks, here are my honest impressions of the product. Simply put, it sticks really well and releases when you need it to. I attempted to run it through a gauntlet of different brands of filament and I couldn’t find one that did not stick well to this build plate. I print a lot of articulated dragons with Silk PLA and with certain build plates, I will have adhesion problems at times. As a person who hates using glue on my build plates, it was a very welcome sight to see that glue is not required on this particular one. Unboxing and Initial Impression Packaging is very straightforward in a cardboard box, inside you will find an information sheet comparing the Frostbite and Glacier build plates that are offered in the CryoGrip series. You will also find a sticker sheet that has the AR code stickers to affix on the build plate for the X1 Carbon to read the proper build plate settings in the slicer. The build plate does have a slightly textured surface but it feels smooth to the touch and feels high quality. The easiest way to describe the texture of this build plate is that it sits right between the Smooth plate and Textured PEI plate that Bambu Lab offers. It also features an enlarged heat-isolating handle on the front with holes to facilitate quick cooling and make the build plate a lot easier to remove from the printer. The information sheet also outlines the settings needed to properly use the build plate. I initially set my slicer to run 5º C cooler but then I increased it to 10º C cooler with no problems. This build plate can also work with all filaments that have a nozzle temperature below 300º C so most engineering filaments will be compatible with this build plate. But where it shines is with PLA and PETG. The Frostbite version is even better at cold printing adhesion than this one with PLA and PETG. The gauntlet test I tested this build plate with numerous filaments. My printer is a Bambu Lab P1S and below is a list of what filaments I used. * Bambu Lab PLA Basic * Bambu Lab PLA Matte * Bambu Lab PLA Metal * Bambu Lab PLA Marble * Bambu Lab PLA Galaxy * Bambu Lab PETG HF * Bambu Lab ABS * Anycubic Silk PLA Dual and Tri-Color * SUNLU Silk Rainbow PLA+ * Eryone Silk Tri-Color PLA * Flashforge Color Changeable PLA * Elegoo Silk PLA * Polymaker ABS As far as performance goes printing numerous articulating dragons and the Midgard Serpent pictured above, the silk PLAs from the different manufacturers did not have any adhesion problems as long as you go with the recommended speed for the initial layer. I did adjust the settings in the slicer to utilize the new Bambu Cool Plate Super tack although the information sheet recommends the Cool Plate settings. I also adjusted the temperature manually to be 5-10º cooler because the information sheet recommends 45-55º C for PLA and 60-75º C for PETG and the recommended manufacturer temps for the ABS. As time progresses I will try other filaments like PA, TPU, and ASA. I would also like to mention that for the 2 weeks I was testing, the build plate was not cleaned at all which is a testament to the stickiness of this build plate. BiQU recommends soap & water for cleanup or even alcohol if you are printing PETG. With that being said, the build plate is so sticky that it can withstand an overnight power outage and resume in the morning with no problems on a cold PNW night. I am quite happy with that indeed. Energy savings with this build plate is going to be significant if you are running a printer farm and running everything 5-10º cooler as a whole. I did not test my particular energy savings on a meter but I am sure it will add up over time. Final Thoughts What can I say, BiQU did a great job with this plate and only time will tell if it is just as durable as the Bambu Lab build plates. If you keep it clean, it should stay very sticky and last a while in a heavy printing environment. My printers stayed running 24 hours a day for 2 weeks straight so it was thoroughly run through its paces. I like the overall texture as it leaves a very smooth finish on my builds and not too shiny. With all of my prints both large and small, I only encountered one problem with adhesion and its because I was printing with ABS and left the top of the printer open accidentally so it was a little too cool in the chamber and the large print warped and came off in one corner. Other than that no problems with adhesion. I give this product 5 stars for quality, performance, and value.

This is probably the best plate you can buy for your 3D printer. Unless you're looking to have a nice pattern on the bottom of your prints, stop here, buy this, and thank yourself. I have not had a single print fail (due to adhesion) since switching. It fits just like the standard plates, and just... works. Very easy to get the prints off as well (though they don't just fall off, they do like to stick, but bending the plate will get things off pretty easily). I would highly recommend this plate for anyone having any issues with adhesion. 45 degree bed temp set, and just click "print" and walk away. No more checking the base layers, no more scrub daddy on your plate every couple prints. I do wipe mine down with a microfiber cloth between prints, but that's just me. You probably don't need that.

Worth every penny for elegoo centauri carbon, stock plates have a lot of adhesion issues. This plate works flawlessly and sometimes can have too much adhesion, which isn’t a bad thing as long as you use a scraper properly to lift the print off without digging into the plate. Hit it with some alcohol and you’re good to go. One note is that these plates are slightly smaller then the original plates, but it doesn’t really matter if you aren’t printing from corner to corner.

I was going through a nightmare of nothing sticking for the past week on my bambu p1s days and I tried everything!! (I used different sides my PEI plate, I tried alcohol, I washed it a bunch of times and nothing worked... I tried all sorts of temperatures speeds and even first layer density and flow, absolutely nothing)! So I gave up and bought this cryogrip plate and it is ridiculous! They say you are not supposed to use alcohol so I just use soap and warm water and this thing sticks so perfectly, the only thing is you can't detach when it's warm so you need to let it cool down before you detach, but now that I've dialed it in it prints perfectly every time! It's crazy, and it's nice because it's a low temperature plate so I print PLA at 40° and pet g at 55° and I don't get any heat warping or creep, I love this thing!

This build plate is really worth it in the electricity and gluestick savings alone - PLA: I've consistenty printed at 35C first layer, then let it drop to 30C after that. I tried it at 30C first but was seeing some slight warping near the edges of the build plate for larger prints. It keeps the chamber temp under 35C, which keeps that loud back fan off. - PETG: I am printing this at 55C. I tried it at 50C first and also saw some warping, so 55C I've had better results. This is with (in most cases) no glue. I was using gluestick at first out of precaution, but this is fine to print on without it, just let the bed cool down first after the print. For larger prints, just sliding the plate out and flexing it as you bring it out will get your part off easily (PETG and PLA). I've tried it with all kinds of brands of PLA and PETG and the results have been consistent. I haven't tried it with any other filament types since it's mainly made to reduce bed temp requirements for these 2. Some cons: I've had some problems with smaller support layers (PLA) and smaller item prints sticking real well to the bed, and needing some work to come off. I'd recommend if you're printing smaller prints, use some light gluestick to help, or go back to the textured PEI plate that comes with the K2 Plus. Outside of that issue (minor), I love this plate and it's my go to for most prints. The only other nitpick is that the surface is smooth. If you want that textured look and feel for your prints, this won't do it. Hopefully they come out with a textured version. Overall I definitely recommend the plate, but it is a little pricey.

With this build plate I can print PLA at 30°C bed temperature. This let me reduce the power draw of the printer so that I am able to run this printer on a 1100VA computer UPS without any issue. Edit: this was possible because where I live the room temperature is above 28.

Worst build plate ever. read all the reviews reporting insane adhesion. The only thing that sticks to this plate is the bubble wrap bag it came in, that was extremely difficult to remove. Despite numerous hot water and dish soap cleans nothing sticks to this plate and the slightest touch will cause it to lose adhesion.