Saker Honing Guide with Whetstone - Red Off-Center Upgraded Honing Tool and Diamond Sharpening Stone Set Kit for Kitchen Knife, Short Chisels and Planes, Fine/Coarse Plate, 400/1000/Grit

I have a fair few chisels which over time I've just thrown in a tool bag and the blades have dulled to make them pretty much useless. I bought this as I could do with sharpening up some blades instead of buying new chisels. I wasn't expecting to be able to get them super sharp considering the state of them It took a long time but the results are great. I would recommend using a bench grinder to get any chips out of the edge but this does a good job putting a nice cutting edge back on my chisels. The guide is easy to use and super sturdy too. The stone seems to take material off quite well although I would like to see a higher grit included in addition to 400 and 1000 as I think I could easily get a mirrored edge with a bit of elbow grease. You can see the state of the chisel I used in the picture and I think the edge has come up pretty well. You can see score marks from the stone so I will look for a new stone with a smoother finish to get my blades as sharp as possible. Overall, a great investment to keep chisels and blades sharp

Nice chisel sharpening kit, the holder is easy to adjust for varying chisel widths and grips well without any movement. Diamond sharpening plate has the 400 and 1000 grades, the 400 is good for addressing any damage while the 1000 provides a nice sharp edge. Would recommend.

Great idea but nowhere as good as traditional oil stone. The guide for mounting chisel is Great though.

Been sharpening chisels and plane blades by eye for 40 years with mixed results. Friend talked me into this system and I wish I'd tried it years ago. Gives accurate precision angles and a very keen edge with ease. My chisels/blades have never looked better. Very pleased with this item.

Very nicely made and simple to use. Good results on chisels

I had completely messed up the angles for both my hand planes by trying to manually hold them at an angle on a different set of whetstones. It took about 45 minutes each to correct but once done, they’re now cutting very well. I did 25 degrees on both and then 30 degrees bevel both using the guide numbers provided. I’m sure now going forward will be fairly quick.

I’d like it a bit longer, too easy to run off the end on the return stroke. Does put a nice edge on though. The paper angle guide won’t last long but any DIYer should be able to transfer the markings to the plastic cover. All in all I’m glad I bought it but think it was a bit too pricey for that set up

So far so good , first time using a diamond stone so bit early to say how good or lasting

great devise , works great . keeps the angle the same all the time.

Desde que lo uso puedo obtener con sencillez un excelente afilado en mis herramientas . Lo recomiendo ampliamente. Facil de usar. Y buenos materiales en su construcción. El rodillo montado en rodamientos es grande dándole buena estabilidad y gira suavemente. Sin duda me ha sido muy util en mi taller. Por supuesto hay otros de mejor calidad. Pero con este y por su precio obtengo muy buenos resultados

Leider war der Artikel kaputt und wurde zurück gesendet! Siehe Fotos. Bitte um Rückerstattung des Betrages! Vielen Dank und Gruß Claudia Prinz

The basic function of the sharpener works well, and I have cleaned up some old construction chisels that are close to razor sharp. That said there is a fundamental design flaw that will often leave chisel edges angled when sharpened as the angle guide uses the backside of the chisel to create the datum for the chisel edge. I have a nice set of Marples chisels that I sharpened, and when I noticed the angle on the finished edge, I measured the thickness of the chisel with a caliper from left to right across the backside that rests against the angle guide, and the thickness varies up to 0.25mm. As the chisel rests on the angle guide on this backside surface, it will inevitably result in angling the sharpened surface. The only way to adjust for this is to manually shim the backside of the chisel resting against the angle guide to make sure the sharpened edge is laying absolutely flat against the stone. Not an easy task! Otherwise this kit works fine and will deliver a sharpened edge. Note that I also finish the edges on a 3000 and then 8000 grit stone.

Buen producto afila muy bien y el accesorio para afilar formones o gurbias planas es muy cómodo