PLA+ Filament 1.75mm, 3D Printer Filament PLA Plus, Dimensional Accuracy +/- 0.03mm, 1KG Spool (2.2 LBS) 3D Printing Filament for 3D Printers, Yellow

I found a 3D model for an interesting skull so naturally I wanted to print it out. A small test print with white filament came out great but the color just wasn't right. Does anyone make a bone-colored PLA filament? Of course they do. I'm not the first weirdo to 3D print a skull after all. A minute of searching brought up this spool from eSUN, and after a few clicks, it was on its way to me. I've used eSUN PLA before and, while I prefer Elegoo by a very narrow margin, eSUN has given me good results. I was a little worried because the skull I was printing would have to be done in 2 parts (skull and mandible), and the main part was a 23 hour print. Plenty of time for something to go wrong. Bambu has a preset for eSUN PLA+ so that's what I used. After slicing, loading the spool, and hitting the print button, I crossed my fingers and walked away. I checked on it again in the morning (12 hours later) and so far everything looked good. Layer lines were visible but not too prominent. Since I was using a 0.4mm nozzle, I didn't expect the lines to disappear. There was a slight gloss to the print. I would have preferred a matte finish to simulate bone porosity, but since I didn't specify a matte filament, I was neither surprised nor disappointed. At the end of 23 hours, the skull was waiting on the build plate. It looked exceptional, without so much as a stray filament, void, or other defect that I could see. The support material (there was quite a bit of it) broke away without much fuss and I was left with something that, from a few feet away, could pass for a skull. Adhesion was just right. The part never shifted during the print but was relatively easy to remove from the build plate once everything had cooled. I did use a little hairspray as an adhesion promoter-- I wasn't taking any chances-- but I doubt that I actually needed it. The mandible was a much easier print (only about 6 hours) and it came off without a hitch. After years of dealing with finicky 3D printers and filaments that would only print correctly about half the time, I was floored that I could walk away for an entire day without looking over my shoulder once and come back to a completed print. I usually pay $10-$12 a spool for garden variety PLA. This spool was slightly pricier at $18, but it is a specialty filament and the price is quite reasonable for the quality and appearance that you get. I can't think of a single bad thing to say about this filament. It worked flawlessly for this project.

Very smooth filament, prints great and I love the color. No issues with the spooling and tangles and it prints great with my tuned PLA settings!

I’ve used a lot of different PLA+ brands, and eSUN continues to be one of the most dependable options out there. The filament feeds smoothly with zero tangles or breaks, and the diameter consistency is spot-on, resulting in precise, clean prints every time. Layer adhesion is excellent, and the surface finish comes out beautifully glossy without needing any extra tuning. This PLA+ also has great toughness compared to standard PLA — parts feel stronger and less brittle, perfect for both functional prototypes and aesthetic prints. It sticks well to the bed without warping, and cleanup after printing is effortless. If you want a filament that performs well across different printers and print speeds, eSUN PLA+ is a solid choice. Great value for the quality and reliability!

The Cold White is the strongest and most opaque white filament I've found - making it ideal for multicolor prints. Most white filament is relatively translucent, which results in a lot of color bleed. I tested a lot of white filaments, and the eSUN Cold White is by far the "strongest" and most opaque, making it a lot easier to get a good white color on a multicolor print.

I’ve used eSUN PLA+ for several projects now, and it consistently delivers excellent results. The Pine Green color in particular is stunning—deep, rich, and professional-looking without being overly glossy or flashy. Why I Love It: Prints Like a Dream: This PLA+ flows smoothly with no clogging or stringing. It adheres well to the bed (I use a glass plate) and layers bond cleanly for sharp, strong prints. Durable and Tough: Unlike regular PLA, this PLA+ has a bit of flex and doesn’t snap easily. It’s perfect for functional parts that need strength but don’t require ABS. Excellent Dimensional Accuracy: My prints came out to spec with zero warping or layer shift. The advertised ±0.03mm tolerance seems legit. No Weird Smells: While not completely odorless, this filament emits a very mild, inoffensive smell—definitely better than ABS or PETG in my experience. Consistent Roll: The filament is neatly wound and tangle-free. I’ve gone through nearly the whole spool without a single feeding issue. Minor Considerations: Requires a Bit Higher Temp Than Regular PLA: I print this at 210°C nozzle / 60°C bed, and it works perfectly. Just don’t assume it’ll behave like standard PLA at 190°C. Color Can Look Dark Indoors: The Pine Green is a beautiful shade, but depending on lighting it may appear almost forest green. Still elegant, just not neon bright. Final Verdict: If you’re looking for high-quality PLA+ that balances strength, reliability, and aesthetics, eSUN delivers. The Pine Green color is perfect for nature-themed prints, miniatures, cosplay props, and durable parts. I’ll definitely be buying more.

So far the best pla I’ve bought. Decided to try a brand that was directly supported by bambu and thought what’s a few more dollars for plus if I have less failures. First benchy already can tell the build just looks better has a shine to it almost and just better quality and experience from the get go. The red is a rich rich color and couldn’t be happier with it. Definitely worth the increase in price, don’t cheap out you save money in the long wrong not having repeat failures and spaghetti. I will definitely be replacing my other filaments with this brand and plus where available! Note: this is the first time I’ve ever been able to clearly read the benchy text on the bottom.

I bought the Bone White specifically to print this T-Rex skeleton. The larger bones printed VERY WELL and very strong. A few bad prints happened on the leg bones and i tried to break each in half by hand. Didn't work. So very strong adhesion. The smaller bones like the ribe cage and spines ,not so much. I tried slower speeds and lower/higher temps to get this to print well on these small parts. 30mm/sec .4mm nozzle at 205c seemsd to have worked the best. But they are fragile and will break if bent. The larger bones , hip and skull were printed using .6mm nozzle. 75mm/sec at 220c and came out strong. All in all, this pla is pretty good, but you gotta know your project and change settings accordingly. I bought 2 rolls to run 2 printers to get this done quick. I have about 3/4 roll left. So i probably won't be buying again soon.

TLDR: terrible winding quality but good plastic I’ve been using eSUN PLA+ consistently since 2022 and it’s always been my go-to filament. Print quality, strength, and consistency were solid enough that I never really considered switching—until now. This particular roll of white PLA+ was wound extremely poorly. The filament had multiple overlaps and tight crossovers on the spool, which led to it catching during prints. As shown in the attached image, this caused inconsistent feeding and ultimately resulted in several failed prints. These weren’t minor issues either—it fully interrupted prints that had been running fine otherwise. It’s frustrating because the material itself still prints well when it feeds correctly, but the spool winding quality completely undermines that. After relying on eSUN for years, this is the first time I’ve had to seriously reconsider using their filament. Based on this experience, I’d recommend others look into alternative brands unless eSUN improves their spool winding consistency. It’s just not worth the risk of failed prints.

Idealny filament na tworczość kościo podobna, za tak niską cenę jakość wydruku jest świetna. Zdecydowanie polecam.

Ich bin absolut begeistert von diesem Filament! Die Qualität ist – wie man es von eSUN kennt – hervorragend. Das Filament ist sauber aufgespult, weist eine gleichmäßige Stärke auf und lässt sich ohne Probleme verarbeiten. Ich habe es mit den Standardwerten (ca. 205 °C Nozzle / 60 °C Bett) gedruckt, und die Ergebnisse waren durchweg sauber und detailreich. Das Filament haftet gut auf dem Druckbett, neigt kaum zu Stringing und liefert stabile, gleichmäßige Ergebnisse. Auch filigrane Details kommen klar zur Geltung, und die Layer-Haftung ist durchgehend sehr gut. Es läuft sauber durch den Extruder und macht den gesamten Druckprozess angenehm unkompliziert. Ich kann dieses Filament uneingeschränkt empfehlen – es bietet eine tolle Kombination aus einfacher Handhabung, hoher Qualität und zuverlässiger Performance. Egal ob Einsteiger oder erfahrener Maker: Wer auf der Suche nach einem hochwertigen PLA-Filament ist, wird hier definitiv fündig!

Estoy completamente impresionado con el filamento PLA+ de eSUN. Como entusiasta de la impresión 3D, he probado una variedad de filamentos, y este sin duda se destaca por su calidad mejorada y su notable tenacidad. Calidad de impresión: El PLA+ de eSUN produce impresiones de una calidad excepcional. La consistencia del diámetro del filamento y su uniformidad garantizan una extrusión suave y sin problemas. Las impresiones resultantes tienen una excelente definición de detalles y una superficie suave, lo que las hace perfectas para una amplia gama de aplicaciones. Tenacidad mejorada: Lo que realmente destaca de este filamento es su increíble tenacidad. He impreso varias piezas funcionales y estructurales con este material, y todas han demostrado una resistencia excepcional. Incluso en impresiones con formas complicadas o delgadas, el filamento PLA+ de eSUN muestra una flexibilidad impresionante sin sacrificar la integridad estructural. Facilidad de uso: Este filamento es muy fácil de trabajar. La temperatura de extrusión recomendada es precisa, lo que garantiza una adherencia adecuada y una fusión uniforme entre capas. Además, la bobina está bien enrollada y no presenta nudos ni enredos, lo que facilita su alimentación a la impresora y evita interrupciones durante la impresión. Compatibilidad y versatilidad: He utilizado este filamento en varias impresoras 3D de diferentes marcas y modelos, y ha demostrado ser compatible y versátil en todas ellas. Desde pequeños proyectos de bricolaje hasta impresiones de mayor escala, el PLA+ de eSUN ha cumplido con creces mis expectativas en términos de calidad y rendimiento. Valor por el dinero: Considerando su calidad superior y su tenacidad mejorada, el precio de este filamento es más que justo. Obtienes un producto de alta calidad que supera las expectativas, lo que lo convierte en una excelente inversión para cualquier entusiasta de la impresión 3D. En resumen, el filamento PLA+ de eSUN es una opción sobresaliente para aquellos que buscan un material confiable, resistente y de alta calidad para sus proyectos de impresión 3D. Lo recomendaría sin reservas y considero que merece cada una de sus cinco estrellas.

Bought it to be able to print an Elf on the shelf for christmas and the tone is a good skin match, prints easy in my Bambulab X1C

eSun has great 3D printer filaments that are highly recommended for all that have a 3D printer. High quality filaments in all colors. I use White and Black the most from eSun! I have tried different types of filament from eSun, all are of great quality! Highly Recommended!