Tailgate Table Rear Foldable Cargo Shelf Aluminum Alloy Storage Shelf MOLLE Panel for Jeep Wrangler JK JKU JL JLU

Nice product. Good materials, stainless steel bolts. Video/Instructions are helpful but miss several points: On the JL, the extra long bushing is for the lower left corner. If you don't have a 13 mm drill bit, standard drill bits are 1/2" & 5/8th, use 1/2" for the 13 mm holes. Then need to angle route the drill bit for proper fit. Instead of measuring location for holes, look for the factory markings on the back of the Mopar panel. It is an easy install.

I like this foldable shelf. I. Like it a lot. It is well built and designed. It does rattle a little while drive. That’s easily fix with a shop towel placed between the shelf panels when they are in the storage position. The unit is made from heavy gauge stamped steel. It has a thick black power coating. When folded down. The shelves are supported with plastic coated guy-wires. The also storage shelf comes with replacement guy-wires, just in case. Installation can be performed in under 30 min. The kit comes with everything needed to install the shelves on either a JK or JL. Though instructions are very vague. For a 2021 JL it’s just a matter of drilling four holes in the tailgate door panel at the appropriate locations. All four were very easy to find. My only problem during installation was the kit included one long spacer and three short spacers. Two of each ar required for a JL installation. Fortunately, I had a small spacer that was the right size to make up the different in length. When folded up, this unit is very thin and takes up very cargo space. Much less space than I expected. Despite the mixup with the spacers. I can still recommend this storage/foldable table unit. The price is affordable and the shelf system will be very useful when out on the trail.

Excellent product for the price but you have to throw away the instructions if you have a JL. Abandon the standoffs. Those are the aluminum collars that are supposed to provide spacing between the painted body and the tray. There's absolutely no reason to use them and they just increase the opportunity of you screwing up. Instead, remove the rectangular top portion design for the factory rail system. You can put that away as you don't need it at all and no reason to drill through it. However you do have to make two small holes directly opposite the two bottom outermost threaded standoffs on the door. This is pretty easy to do. Put the aftermarket screws in the holes to almost flush level with the panel. Just have them stick out a quarter of an inch. Then coat the heads will you put the screwdriver in with thick grease. Just a dab on each one. You're not going to use it for lubricant. Now position the top part of the black plastic panel you pryed off. Make sure it's perfectly centered. Then swing the bottom down and contact it to the screws. It should not be enough to clip it in as the screws should be preventing it. Now remove it again and you should have two grease marks on the back of the panel from the screw heads. That's where you're going to drill. Drill a 3/8 hole from the inside out right in the center of those Grease marks. Remove the screws and clean them up. Now put the black plastic panel in without that rectangular insert you discarded. Now install the Trey using the four bolts washers and lock washers. You will be able to get the tray flush up against the plastic interior panel. It may be a little difficult to get the bottom screws because of the angle so I recommend maybe using an allen head at the end of a quarter inch driver extension? Either way you can get it in there. Don't torque them down too tight or you'll crack the plastic. That should be it see the pictures. Very flush and professional looking.

No drilling required, which was what really sold me. I had previously tried another shelf that was "bolt on direct fit for JKU" and it wasn't, so I was a little nervous about this one. Pretty easy install, about 20 mins. The bottom right mounting bolt gave me a little difficulty, I'm assuming something is blocking the bolt from sitting perfectly vertically. This works really well when paired with a glass mounted LED strip as pictured, creates a nice little station for your overlanding needs. Also some people were worried about a rattle with this, the dual latches keep it tensioned very well and I don't hear anything over your standard Jeep noises.

A lot easier to install than I was expecting. For some reason one of the standoff's is shorter than the others.. washers filled the gap. The cover has markings on where to drill.. I didn't have any issues with rattling and i have the Alpine setup.

Great item, but lacked a little. First I have a JL, so i took the cover off the gate and found the drill points easily. When I put the cover back on and inserted the plastic sleeve bushings, only one was longer but two longer ones were needed to make the shelves even. So i had to find a nut to add to one of the short sleeves that made up the length difference and then attached it with electrical tape to stay in place. Thankfully I fond one that fit the bill. Once everything was installed, the unit fit well. One small thing, the top shelf was hanging at an angle. Photos included. So i'll have to figure out a way to make that small shelf hang even. So, for the price I guess it's ok. I will say it is well built and heavy.

I was torn between giving the EOIS Tailgate Table Rear Foldable Cargo Shelf 4 or 5 stars. I really liked the end result of the installation, but after adding up all the annoyances of installation and the clear misrepresentation of it being aluminum, I decided on four stars. I installed the unit in a Jeep JLU 2024 Rubicon. The Good: -- I really like the unit as a whole. It's compact, folds up nicely, and does not rattle when driving. -- The latches are very secure and strong. -- The molle pattern is excellent, and it is the main reason I purchased this one. I hang Molle bags off of it, and these lay underneath when the shelf is deployed. This provides a very efficient use of space in the back of a Jeep JLU. See picture -- It's offset from the rear panel. See picture. I was concerned that it would rub against the Jeep's plastic rear panel, but while measuring for the mysterious longer spacer, I realized that the panel is actually offset about 1/4", leaving a gap between the shelf and the Jeep's door panel, which is great. -- The Jeep's rear door panel needs to be removed, and it is very easy to do so. With a little gentle prying with a plastic tool, the panel just pops out and then easily pops right back in. -- A 1/2 inch drill worked fine for the holes vs the stated mm size in the instruction that needed to be drilled in the Jeep panel. The Bad: -- NOT ALUMINUM: The seller claims this is aluminum allow in the web page description. It is too heavy to be aluminum, and testing with a magnet, as shown in the attached video, confirms it is made from steel. The only aluminum used is the four spacers used to attach the steel shelf to the Jeeps rear door. -- Very poor instructions. Someone handy and understanding of working on a Jeep should only attempt this install as you will have to figure out some things on your own due to the poor-quality instructions. -- They provide one spacer much longer than the other three! Why? It must be a mistake. After much measuring, we determined all the spacers should be the same size and hacksawed the long one to match the others. This is really poor execution on the EOIS part. -- The top shelf is not level, and there is no easy adjustment. It tilts down. -- After some discovery, we found that the holes to be drilled were already marked with dimples on the inside of the plastic door panel. It would have helped if there was more information in the instructions and pictures. We marked these locations with blue tape in the picture. Some hints in the instructions for this would have been very helpful.

fit great, easy install.

Easy install for the Jeep Jk Need to install some Molle bags or put a towel in between the 2 shelf’s when in the closed position or it will rattle. It’s a super easy fix and if your mechanical in any way you can change a few parts to make it even better for low cost. But as it is , it’s perfectly fine. When installing the mounting posts, you leave them loose as per instructions and then mount the table on the studs. Now put the nuts on but just finger tight. Then tighten the mounting posts. After that, when you tighten the nuts on the studs… there is t much thread so only tighten until they stop, if you over tighten, you will break off the stud. I also put some weatherstripping in some areas that could’ve possibly caused some rattling, but it may have been unnecessary. It’s a solid table and I really like it only had it out a few times where it was actually used for camping and it’s been absolutely fantastic. The cables that hold the shelves have held up nicely, although I may replace them with something a little more robust.. for the price point. This is good and it works.

Mesa muy útil y práctica, fácil de instalar, en el Jeep JKU, no se requiere hacer ningún orificio, viene con todo lo necesario para su colocación en la puerta trasera del auto.

Jeep Wrangler Jk 2011 70th Edition Kofferraumklappe geht wegen dem Subwoofer nicht zu. Musst ihn ausbauen. Montage selbsterklärend und relativ einfach. Robustes Material. Die Schnappverschlüsse neigen leider zur Schwergängigkeit, Gefahr die Finger zu quetschen. Die Fangseile verklemmen sich komisch zwischen dem Tisch und der Halterung. Verbesserungspotential. War leider über der Rücksendefrist, sonst hätte ich ihn nicht behalten.

Fitted to UK Jeep JK 07 and it was really straightforward and works very well. Very pleased so far!

Love this, it fits my 2021 jeep sahara limited. Easy to install.