Adjustable Mold Housing Kit for Silicone Mold Making - Leak-Proof Plastic Frame for DIY Resin, Candle, and Soap Molds - Reusable Craft Holder with Free Combination Design for Jewelry & Epoxy Casting

Great means of replicating concrete sconces. We made 3 molds from the one gallon kit, only because the resin initially leaked from from the bottom of the form, so use a better means of sealing the form to the base as the double sided tape is thin and tantamount to useless. With forethought I also purchased an extra set of mold forms for a deeper pour.

Curing shouldn't take as long as some reviews complain about. Either they had a bad batch, added too much pigment, or didn't mix it completely. Mix it until there is only one green color. No streaks of white. No spots of light or dark green. Mix it for a couple minutes like the instructions tell you and you'll have no complaints. I only used it for the 75ml cube in the photo and I'm sure larger batches will require longer mixing. You'll have over an hour before it shows any signs of setting so you'll have enough time. After properly curing, there were no bubbles or wet spots throughout the cube. There was a tacky feeling like new rubber or silicone as you'd expect. As you handle it, the silicone mold will pick up dirt and oils from your hands and lose its stickiness like tape does. If you want to get rid of the feeling faster, throw some baby powder on it or rub it on your pants. It'll pick up the fabric and lose any stickyness. I used it to make a tab for an AC return vent screen. After I made the mold, I used JB Weld for the copy. Even without mold release, I could easily remove the copy. It's not a complex part but it was able to pick up fine texture details like where the paint on the original was chipped. The silicone is also strong enough to cut open, grab the part, and snap back into place for another copy. Any imperfections in the copy were from my lazy mold making and not getting the bubbles out from under the part. There was some cleanup involved, but a little extra shaking or prep work would have saved me time trimming later. The mold walls are convenient, but use better tape or another method to seal the bottom and sides. The silicone is very low viscosity and will pick up tiny details. It'll also find every little crack and try to pour out.

A 4 out of 5 is kind of right. I love the product, I just wish there was some way to make inside corners. Example; I was making a resin cross and all I could do was a square, to make a square for a cross seems such a waste of silicone. Other than that little thing, it works great, just as it should.

Cool. This will help a lot. Just getting started in making molds. So wish me luck

I Recently decided to try my hand at mold making. the first frame I brought was from another company, it worked well. I wished to make another mold but needed more sections to make it bigger . This one was cheaper but looked about the same as the other one I bought. To start with it was smaller then the first. I decided to try it out anyway . the sections did not fit together very well . I sealed the bottom with my glue gun , used the tape on the joints . it still leaked badly. after I finished I could not get the tape off. I ended up ordering from the other company.

functions just as shown. It's sturdy, no leaks, can change the size, and the a fine job. I just wish it came in larger sizes!

FYI this does not come with a bottom. I’m not sure if that’s normal, but you have to rig your own bottom. Aside from that, it’s functional, easy to disassemble/assemble, and seems pretty strong.

This silicone kit is about as easy as it gets. Simple 1:1 by volume mixing. Just mix the A&B parts together for about 3-5 minutes, then pour around the object you are molding. Reading the instructions, the product claimed bubbles would all go away after 2 hours, which made me very skeptical, but I have to say I was pleasantly surprised because I expected to need to use a vacuum chamber in order to pull bubbles, but to my delight it was not necessary. I have used Smooth-On products in the past & did not have the same luck at all. Considering there are a ton of similar products on the market & all are around the same general price, I would gladly purchase this again due to the ease of use & especially the lack of bubbles in the final product.

I purchased this liquid silicone to make moulds of items I want to cast in Resin. To be honest, I have not tried this product yet, however, when I start to use I will update my Review and tell what I thought of the product, the hardness and what my thoughts are of this “Liquid Silicone” are!!

You would think there would be no leakage through the joints. What a mess. Cleaned up, for round 2 I'm using a bead of silicone adhesive in the joints. Will see how well it works this time.

the silicone mold liquid leaks out from under it - would be much better if it had a sealable floor with it

يجب الإنتباه قبل الشراء حيث أن المنتج الذي وصلني عبارة عن اجزاء الإطار البلاستيكي مع مشابك للتجميع فقط بدون قاعدة، اي انه عبارة عن اطار ليست له قاعدة ليتشكل لدي صندوق لصب الصابون، وبالتالي لا يمكن استخدامه بشكل أو بآخر في تصنيع الصابون ولا انصح به

Excellent product