VIVO Micro-Gap Flat TV Wall Mount Designed for 43 to 85 inch 2021-2023 Samsung Neo QLED (Excluding QN95C Series), and More, Ultra Slim Profile, Mount-TVSG1

Works well with frame tv and as good as the original Samsung bracket. Detailed instructions are helpful and the drywall anchors are of top quality which is rare to see as the included anchors are almost always cheap plastic type. Measure correctly and go blindly with the placement of your choice regardless of the stud presence as anchors can easily hold heavy loads

I used these to hang a 86-inch tv and they work out very well. Easy install. Keeps TV against the wall nicely.

This mount is SO different and actually amazing. I am very glad I went with this one over a traditional style mounts that are so abundant. While it took a little to get the hang of getting the tv hooks to seat in the wall part, but once you get the hang of it (as I asked my wife to help me about 4-5x : ) It is just fine! Here are the key points: PROS: +It is very low profile. +It 's not advertised, but you can TILT the tv a few degrees down by foam/padding etc on the back and top of the screen! +It is Height (up and down) and L and R (to tweak level) ADJUSTABLE! Because of the above, it gives you some grace, to move the tv up, down or left/right mounting. The wall brackets, AND adjustable tv brackets on the back of the tv which depending on how wide the wall mounts are placed, it can adjust the height a solid half inch! Again, this thing is SO different than the traditional flatscreen mounts. Which is a benefit, and you have to wrap your head around it. They have a sophisticated instructions, which look like they would work, but me, being the DIY maddog of a hacker, I just built an exact template of OUR flatscreen, and drilled holes in my 'Prop TV' and then was able to align it with some confidence. Especially since drilling into bricks would be a hassle to re-drill additional holes. This mount, I think, was designed by a gifted engineer! Regarding THIS installation in BRICK. I have an almost 10' tall brick fireplace wall that goes all the way to the ceiling and thus the mantle was a tad high--top was at 63.5". And for the flat screen tv (Samsung 55" CU8000 series 1" profile) to mounted above it, I was looking at around 65" for the bottom of the screen. Just a tad high in my opinion!! So I thought it was going to be a day or two project...NO! It turned out to be a 6 to 8 day project!! I ended up tarping off the whole area, cut bricks off, etc and built a fold-out new mantle that was much lighter, and hollow so I could run cables thru. (Hard to believe but I was able to lay the cables in FRONT of the brick, cover them with aluminum tape and with paint you would never notice them! I guess the asthetic of the rough brick leads to that look, but wanted to mention it, so that others realize you don't HAVE to run cables behind the brick) The Mount, being LOW profile and the tv being only 1" thick gives this a nicer look, I think! CONS It's not the 'cheapest' mount, but I think for the features this provides, I think it's totally reasonable! Great value.

Good clone of the Samsung mount. Not as good bolts quality as the original has. Aside from the hardware quality all good. There probably no reason for separate mounting points for the wall part. It makes installation overly complicated for no practical reason. But the same goes for the Samsung original mount.

I'm very happy with the finished product. I wanted to hang my Samsung Neo QLED QN90C as close to wall as possible, like a picture frame, with all the cables run behind the wall. This bracket allowed me to do that. This mount was less than half the price of the very similar Samsung brand/version, as well as a lot of other flat wall mounts which are not as low profile. The instructions were a bit confusing. Just measure everything multiple times! You CAN set these brackets in drywall only, but it's always more secure if you can hit a stud. The amount I saved vs other brackets paid for all the parts I needed to run electrical and cables through the wall.

These went up pretty fast. Follow the instructions and you’ll be fine. To be honest, in hindsight I probably should have spent the extra $10 and bought a single mount bracket, rather than this item with the two separate pieces. It’s kind of annoying trying to hit some framing with this setup. Also takes some extra effort to get the two level to each other. Not terrible though. That was the only annoying part about the installation. Everything else was good. If you’re looking for a bang for your buck, these suffice. If you have $10 to spend, look into the single bracket styles. Once installed, you can level your tv by sliding it around. It has an unusual action and may take a little back and forth, but it’s easy enough. They include foam spacer pads. I didn’t use them because the whole idea is to get the unit as flush as possible. It sits less than 1/16” from the wall all the way around. Good enough for these days.

Slightly disappointed but entirely my fault. I didn’t have my electrician countersink my outlet so now the entire weight of the TV rests on the plug. I do have a run installed to another plug but drywaller covered over. The bracket fit is so tight I can’t get the TV back off the wall to fix. There is absolutely zero play in the mount for adjustment once it is up. I used my own lag-screws for the studs and their drywall anchors (initially). Their’s pushed right through the drywall. I wanted my TV centered on the wall but when centered the brackets (~14” long) were positioned right between the studs so I had to offset the TV position. When I had my wall brackets spaced properly to fit the TV bracket, no holes lined up with the studs. I had to extend the wall bracket holes by grinding the metal. Since there is no room for error or adjustment, they should just supply a solid template but maybe the 2 mounting options are not ISO across brands or models. Measure and level 3x before drilling.

This was super easy to use and worked perfectly. It is versatile in where you can put the screws/holes to make sure you hit the studs. It hangs the tv close to the wall so that we can use our new Fire TV with ambiance like a frame tv. It is great quality and gave us the look we wanted. I would say we did use the Fire Tv but the back of the fire tv is a little bulkier than expected so we have to build a thick frame for it but worth not paying 1k

Suporte slim mesmo, a TV fica rente a parede. Isso dificulta a instalação dos aparelhos e passagens dos cabos, mas nada que um manuseio cuidadoso não resolva. O suporte é robusto, feito de material de qualidade.

Excelente material, muy buen producto

This was used to mount a 65" Samsung S95C OLED and it leaves almost no gap behind the TV, perfect. This is exactly the look I was going for and did not want to spend the over inflated price for the OEM mount. Install is straight forward if you've hung TVs before and it comes with templates to locate the mount. Hanging the TV was a bit tricky with one person but would be easy with two. I would not have a problem using this mount on a larger TV but only necessary for an ultra thin OLED in my opinion. Would certainly recommend to others.

THE BEST TV WALL MOUNT BRACKET EVER UNMATCHABLE QUALITY AS SOON AS I HELD THE BRACKET IN MY EXPERIENCED HANDS, I COULD LITERALY FEEL THE QUALITY. THIS WON'T BE COMING OFF MY WALL ANYTIME SOON, I CAN TELL YOU THAT AS A FACT

Excelente. La mejor compra que pude hacer, es muy resistente y mi televisor quedo literalmente pegado a la pared