GE Appliances WD28X10284 Dishwasher Lower Dishrack

Dimensions and wheels fit this older model perfectly! Inverted V-shaped dish supports are a fantastic improvement over the old tines.Original silverware basket does not fit and so consider also buying the recommended new silverware basket.One star off value for money... the cost of this rack is 1/3 the cost of a new dishwasher and yet, this is our choice because our old dishwasher works perfectly well, but the lower rack had rusted through.

Calling this rack Junk is being kind. It's slightly narrower than the original part so the wheels constantly fall off the tracks, usually when it's fully loaded. There are already tiny rust specs in some joints after a few months of normal use, which must be patched using food grade sealant or they will quickly spread. The arrangement of dish holders is 'ok'; not as good as the original factory part, but adequate.This is the second replacement I have purchased. The first completely rusted out in sections and began to fall apart after 14 months. The original factory part lasted many, many years longer. Now I'm left with a perfectly functioning dishwasher that requires a new lower rack every 18 months and new upper rack every 24 months, because GE can't be bothered to produce quality replacement parts. It's disgraceful. What is even more disgraceful is charging this much for this piece of garbage.

Wheels are smaller than original but no issues so far.

Our old rack was rusting away. Had a problem finding a reasonably priced replacement, most were $150-$180, might as well buy a new washer for a few hundred dollars more. The wheels are undersized so the rack sometimes slide off the track. I took a couple off the old rack and put them on, then it worked fine. Sometimes find the wire guides make it difficult to get full sized plates to fit prop. Other than that it works fine . Not perfect but price is right

The lower dishwasher basket casters were bent and did not roll in easily. It seems like it is almost too small for the dishwasher and easily comes off the track when rolling the basket in and out. I'm very disappointed in this product too and I already threw out the original rack, so I'm stuck again! Very disappointed!!!!

I like it because it works in our old dishwasher and I don’t have to buy a new dishwasher.

Good product, good price, fits my Hotpoint perfectly, and the coating and dish prongs are well set up; the only slight draw back is that the new wheels are still fairly thin, and so you would want to salvage your "old rear wheels" and put those on to the new rack, as the new wheels are too thin at the rear of the new rack, tend to have the rack slide off the track or ledges.

This is the suggested replacement part for my Kenmore model 363.15165793 dishwasher. It is too narrow for the bottom ledges. The wheels always fall off one side. I tried replacing some of the wheels with my old rack's wheels because they are wider, but that still was not enough. The sprayer in the bottom does not line up properly with the hole in the rack. I run the dishwasher about once a week, occasionally twice a week. I have owned the rack for 5 months and the plastic coating is already wearing off in many places, which leads to rusting. The EXACT reason why I replaced my old original rack. (I couldn't put any cover-up on it any more - it was more cover paint than rack at the point I bit the bullet and bought this rack.) The original rack lasted for YEARS, so it's extremely disappointing to have this not even last ONE year before rusting. What a waste of money because now I have to get some more of that cover-up paint stuff for the rack too. I also hate that it has these inverted V prongs rather than the single vertical prongs that the original rack had. It made fitting dishes more awkward.

The front wheels are narrow there are 4 of them, the rear is thin, the front ones are wider and the rack does not fall in the dishwasher. The rack is the same but the thin wheels make it not usable. But I removed the front four wheels and put them on the new rack and all was well, again the original had wide wheels twice as wide as the rear?? Otherwise, it's fine, but if you don't have wide wheels to swap them it will not fit properly. It also seems a bit pricy for a wire rack. But thay are like most parts expensive.