GeeekPi ICE Tower Cooler for Raspberry Pi, RGB Cooling Fan with Heatsink for Raspberry Pi 4 Model B & Raspberry Pi 3B+ & Raspberry Pi 3 Model B

Absolutely love it! Looks amazing, fits really well and assembly is easy. I'd recommend using a traditional thermal paste however a thermal silicone pad is provided. The rgb led is permanently on but a black fan was also provided in the kit should that be your preference. Works on 3.3V or 5V pins so there is 2 options for fan speed and led bright brightness. Comes with a white acrylic base plate that does the job perfectly well if you don't have a case on already. Fan I find is very quiet and keeps the processor super cool, perfect for overclocking or just turning your pi into a mini pc ;) Highly recommended all round.

First I should point out that the box I received had Pi 3 model B on the side label but I had a Pi 4 (worried ....) In the box was only 1 set of brackets not 2 with no label on them (worried more ....) BUT they did fit the Pi 4 as expected (I think maybe the V 2.0 of this product may have a universal bracket set now ?) I used MX4 thermal paste instead of the included sticky pads which worked well. I intended to build a fan controller with a MOSFET but it is fairly quiet and I have not needed a speed controller as yet. Also the V 2.0 fan is not just the blue led but changes colour and intensity constantly, it looks quite cool. The kit also comes with a perspex base plate which is useful and protects the board from scratching the surface it is on as you can't use any case due to height of the cooler. Now for some temperature results :- Pi 4 has no case and is overclocked with overvoltage=6 Arm_Freq=2147 and GPU_Freq=750 (so pushed to the very limit) and running 64 bit kernel. Room temperature at 23 C. When idle on the Raspbian desktop the temperature is 30 C or lower ! When pushed with 'stress --cpu 4 --timeout 360' command to load all cpus to 100% the temperature at the end is only 43 C and drops back below 34 C in a matter of seconds once command ends. The whole Pi 4 is much snappier and very usable for general desktop process now. Only negative is I can't fit the 40 way ribbon cable for my t-adapter/breakout board due to too little gap between the cooler bracket board standoff's and the GPIO pins. I can however run individual pin cables across to the t-adapter which is fine as I don't need that many, never needed anything close to all 40 at any time. The best product I have ever added to my Pi. Edit: I have found that a GPIO header riser fits OK and the ribbon cable for the breakout adaptor can be attached to the riser without any issues.

I love how easy and fun it was to put together and install. It fit my 3B+ perfectly. I wasn't keen on the pre installed color changing fan so I swapped it for the included plain black one. They also provided spare screws and fixings in case you misplaced the original ones. The fan is whisper quiet and keeps the pi nice and cool. I love this tower cooler and I am going to put one on all my raspberry pi's. Would strongly recommend.

Good Cooler works very well and is quiet, idle temps are down at around 24 degrees, not seen anything above 28 yet (overclocked to 2.1 GHz) Foam packing makes a nice pad for the whole thing to sit on, keeps it extra quiet. They packed a bunch of extra bolts/nuts so that was nice. Bad Brass standoff things have screws which are a little too long. Causes a lot of rattling as the actual board is loose. Cut them down with some pliers. Note I didn't use the included thermal tape, I used paste.

The product is perfect for cooling my rasperry pi 4, I used before other solutions like small heatsink fins and even an aluminium heatsink case without having similar results. With my previous case (an aluminium heatsink block all around the raspberry) the raspberry temperature was hovering around 50 degrees celsius, with peaks up to 60-65. Since upgrading to this heatsink, my temperature has gone down to ~33 degrees celsius (I attached a screenshot of the temperature graph), with a maximum of 35 degrees celsius. I haven't tried to overclock the raspberry yet, but it's clear that with this heatsink you have so much more headroom. I attached the fan to the 3v3 pin on the raspberry and it's super silent (~ 38dB - same as a good grade "Noctua" computer heatsink). The LEDs on the fan give it a "computer modding" feeling that is quite nice and captures the attention, these are automatic. The only downside (if you consider it a downside) it's that it occupies more space compared to other solutions, and it's quite difficult to find a case in which it fits. This is not a problem however If you do like me and decide to keep it outside a case. It looks so cool that I don't want to hide it away anymore :D Overall, this ticks all the boxes, It's perfect!

I hadn't used my Raspberry Pi 4 since it was released. The high heat load and the lack of USB boot meant that I'd kept my Pi 3 working and using that instead. However, seeing this, and that the heat of the Pi4 had been reduced through firmware updates, I took the plunge. I installed and then used the Pi 4. Running at 100% load on all for cores over night saw tempertures only hit 45°C, which is a fantastic improvement over the previosuly seen loads. I set mine up with the attached thermals pads - I didn't have any thermal compound around the house to see what that would do, but I'm happy with the limits I'm at. Noise is reasonable - on my desk, it sounds about as loud as an external drive being accessed, so I have no problems with that. Light wise - it might be nice to have a version without LED's but again, it doesn't really bother me. Overall, very happy with this.

I had only had my new RPi4 a couple of days and I was already causing it to hit 80 degrees (celcius) with the various things I was doing, so I needed to do something. I thought a passive case would do the trick, but I was wrong. Seeing how chunky it was and reading how successful it was reported to be online, it was a no brainer. It was pretty easy to fit, and I had no issues with it fitting snuggly against the board. The results were striking: With no kind of tinkering, the temp went from 80 => 43. With various little config changes to push the board, including pushing it to it's limit with overclocking, it remains (until this day), around the 52 degrees mark. The only time it has gone any high (around 60) was when it was a particularly warm day, but a change of environment quickly remedied it. Totally recommend it.

Have tested about 5 different coolers for my Pi4 and this by far is the best regarding temperatures as well as noise (can keep it by my bed). Lovely little cooler, comes with two fans. One with light and another black one without light to meet our needs.. Fair price comparing to other Pi4 Coolers but high for such a tiny device. Better than almost "silent" Noctua. Recommend it with a pleasure, would buy again.

Purchased at least a dozen of these cooling towers to use for Bitaxe 601 and 602 miners. They work great, reliable cooling. I do not use the stock fan that these come with since I am not connecting these to a pi board.

all great, look and installation, reduced temperature, silent fan so far (dunno how long it will be over time)

Bütün parçaları tam, eksiksiz geldi. Kurulumu son derece kolay. Rgb renkleri güzel. 34-36c civarında işlemci sıcaklığı var. Fan çok sessiz, yanında rgb olmayan yedek fan bile göndermişler. Kendi heatsink yerine mevcuttaki sıvı heatsinki kullandım.

استبعدت المروحة السابقة وأضفت هذي.. خفضت حرارة الراسبيري من 40 إلى 34

He proba otras opciones que e no me han funcionado. Ésta me mantiene la temperatura de la Raspberry pi 4 a raya y además no se oye nada, teniendo en cuenta que yo soy muy exigente con el ruido. Subte molesta las lucecitas cambiantes que tiene creo que se pueden desactivar. Llevo más de 1 año usándolo y nonhe tenido el más mínimo problema. Lo recomiendo.