Dorman 47137 Windshield Washer Nozzle Kit Universal Fit

I installed these on the hood of my 86 chevy truck. The hardest part is deciding where you want them to go. Drill 2 holes and put it all together. They work way better than my old wiper arm mounted sprayers!

I wish I knew these existed long before I bought them, I had been meaning to replace my factory ones since their coverage was too small and they had begun to fail. I contacted the dealer (Honda) and they wanted around 30 a piece for the nozzles. Safe to say they didn't get a dime from me.I had some corrosion in my old lines so I replaced those along with my nozzles. Removal of the old ones was simple with a pair of needle nose pliers. I then cleaned the area where the old ones were before installation. Now these come with a gasket and then a plastic twist on screw which is self explanatory. You can do it yourself or have someone test them to make sure they are pointed in the right direction before tightening them down. Remember it's plastic so hand tighten the screws or very gently with the pliers. Once this is done go ahead and test them out again and check your coverage, the kit comes with an adjustment tool just in case.Pros: Cheap and well built, very simple to install, make sure they're compatible with your car, mine was a 99 Honda CivicCons: The fan style spray was a little too wide for my size car and it hits the top of my A-Pillars so if I had the windows open water can sometimes drip inside, again this depends on your car.Recommendation: If the dealer's asking too much give these a shot, they could be a simple solution to your problem. Just make sure they fit your car!

Used this washer nozzle kit when I replaced the factory hood on my 06 Wrangler and did not want to cut holes in the new fiberglass, high line hood for washer nozzles . I drilled a hole in the center of the cowl for one nozzle. The metal nozzle in the housing is adjustable so was able to get it to spray well on about 60% of the width of the windshield. Heightwise it covers top to bottom even when moving. It cannot reach the far sides but the wipers are able to spread the fluid over to the sides well enough. The kit has gaskets for under the nozzles to protect the paint. The nuts are plastic so am concerned over time it might get brittle but since I only used 1 and there are two in the kit, I have a spare should anything happen. The housing is plastic but the nozzle inside it is metal (brass?) and overall this is good quality as you would expect from Dorman.

The Desert Sun and heat destroyed the silly clip-on factory wiper blade sprayers and a fitting to a rubber feed line. I ordered this and a plastic 'T' and some rubber vacuum tubing and took a chance that came out perfect! This is a full size 1997 Dodge Ram B3500 extended van. I drilled the holes through the bottom using the little nick in the pressed panel as visual alignment so I didn't even have to measure! I put on a section of tubing and ran it over to the battery side on the right where the washer pump hose comes up into the hood by the hinge. I tie wrapped the tubing along the wiring to the hood light in the center. I added the plastic 'T' under the 2nd new sprayer and clipped the washer line going into the hood and connected it. I used the metal adjusting tool to raise the ball adjustments all the way up. I get a perfect mist pattern that works sitting or moving! Perfect install it would be a true 5 star if it came with a plastic 'T' as they all cost about $5 and up so I just ordered a $8.99 kit with many different sizes for future projects...

I have a 2007 Jeep Grand Cherokee and my washer nozzles broke at the inlet. As it's a common problem for my car model, I got this product thinking that the extensions would relieve stress on the nozzle inlet. It also helped that this is 1/4 the price of my OEM nozzles. Installation is easy overall and although the plastic is very glossy and they're a bit boxier than OEM, I think only I'll know that I put cheap nozzles in. But I found 3 issues which caused me to rate this product so low:1. The short tubes provided are not very stout, so I had to carefully route it to keep the tube from kinking (no fluid comes out when the hose gets kinked). I was able to get both kink-free, but I have concern that the tubes will kink after driving around.2. One of the two nozzles didn't produce any pressure, so the fluid came out as a stream rather than a spray, not allowing the fluid to get anywhere near the windshield. I contacted Dorman, and they suggested washing in warm water and blowing air through it, which to my surprise actually worked! Still listing it as an issue, but one that can be easily fixed.3. After getting both working and aimed, I found there's a lot of fluid that drips around the nozzle. There is plenty of spray on the windshield, but I am very dissatisfied with pools of fluid around the nozzles after a spray. I didn't see this in any other reviews, so not sure if it's just my car, or if nobody else really cares about this issue.I gave this a low rating mainly because of issue 3; it really makes this a less than mediocre substitute in my opinion. The first two issues caused a little grief, but were easily overcome and in my opinion would've been well worth the cost savings.

My car is an older Honda and had the old style nozzles the two hole spray instead of a fan. This replacement worked great. Super easy to install and the fan style spray works so much better. And for all the people saying this sprays the cleaner too low, the kit comes with a metal tool to adjust the level of the nozzle. All you have to do is adjust it to spray higher and you're good to go.

Sprays a little low on the windsheild of a pt cruiser but still works and not a big deal since the wipers spread it.

It did fit although it says universal. Works good , had to adjust the nozzle sprayer but took me 20 seconds

So my only comment on this nozzle replacement kit is that the stream it produces on my SUV is different than what the OEM nozzles produce. And even though these Amazon replacements have a range of adjustment, it's not possible to replicate OEM. They get the job done though....

I had no difficulty installing it, very easy and fast works fine. For the price it's worth it. for around 20$ for 2 it's a bargain.