MotorGuideMGA015PB6 Mounting Isolator Kit — Absorb Shocks, Protect Electronics — Includes Corrosion-Resistant Bolts — Set of 4

So far so good. Was a little skeptical at first after reading a review of them ripping out due to not having enough fiberglass to grip. Once i drilled into my hull, i only had a depth of maybe a 1/4 to 1/2 an inch of fiberglass for these to grip on to, so without any other options, I proceeded with insallation.Insallation was super easy, and just so you know, you have to screw down on these a lot..... a lot. I seriously thought the screw was stripped, so backed it out and the screwed it in while holding it. Nope, just takes a lot of turns of the Ole screw driver if there isn't much to grip. It will tighten to where you cant turn anymore, just keep going till you get there.The motor held fine during trasport. I then moved boat to 5mph with gas motor and my wireless bow mount as a rudder just to see the torque. It worked great.I ordered another set to keep on boat just in case one does pop out. Been out so far 6 times and still holding strong.In the instructions it informs you to tighten after your first trip. I just tighten after or before every trip just incase. And if I have room, I just transport bow mount motor in truck or boat just to keep pressure off of mounts.defiantly worth the money and a great option if you have no water to get under bow.

I had never mounted a trolling motor myself on my boat, it came with one, and I was about to replace the whole thing (mount included) so I removed the old one...long story short, I ended up putting it back on and needed new mounts. I would have needed them either way...Removing the old mounts actually proved to be harder than putting in the new ones! I followed the simple directions (paraphrased here):Put the rubber mounts in pre-drilled holes of (X size).Set your motor mount on the rubber isolator tops, align holes.Firmly press down on the motor mounting system to be flush with the rubber mounts, and make sure the rubber mount is flush with the fiberglass on your boat.Drive the screws in to pull the rubber up and hold your motor mount in place. (pro tip - USE AN ELECTRIC DRILL / SCREW DRIVER for this)The steps are really that easy. And it works great. Not that there was any surprise, it's a simple concept, and a simple implementation. One thing you SHOULD be aware of though-- if you set your front holes (or if they were previously set) too far forward, you need to be careful the front bolts are NOT TOO LONG. If so, you will punch right through the bottom fiberglass...mine was that way and instead of remounting slightly further back, I just used the shorter bolts in front. No biggie.All in all, a great product that works fantastically. Easy to install and will last for years. 5 of 5 for me!

These are actually very nice mounts and easy to use. I highly recommend, however anyone ordering should order a second set as a spare. The very design of these will not last forever. In fact, my first set of these just failed on the water. Glad I had a second set onhand on the boat and a phillips screwdriver in the boat toolbox. Took 15 minutes to replace with a new set on the water.Now for the problem...the design of the mounts are to isolate shock and torque from the mount holes through the fiberglass boat deck. They truly do the job for this....no deck cracking what so ever after three full years of fairly hard use. However, this advantage comes at a price. The mounts are rubber and will eventually tear through/separate from the brass threaded tightening sleeve. When this happens, the mounts will have no grip and pull straight out. Fortunately, my MG gator mount has four of these, and motor torque only tore thru the 2 isolators on one side of the mount.When I replaced, I did all four of the isolators....glad I did, as the other two were about to fail as well. When the two did let loose, the mount looked as if it was going to fly off the boat, but the other two held. Lesson learned....although you're not supposed to have to get access below the deck to use these mounts, I WILL be adding a washer and nylon lock nuts to make sure the next time they fail, the mount doesn't try to jump off the deck:) My heart can't take that anymore!Excellent mounts though, I'm back here to order two more sets for spares!

Good product but came with only two screws.

This was so much easier than searching all over for these. One click and that’s it! They arrived quickly and were easy to install. They are nice and sturdy!

Unable to access the underside so these were perfect for my MG trolling motor. They keep it secure but will rip up if you hit a rock or something. Oh well, just buy another set and reinstall

The are a perfect factory replacement and works perfect. I use a little antisez on the end of bolt. The old one were seazed up and had to be cut off .

After 12 years my motorguide started to move and jumped when I changed to a higher velocity so I knew it was time to change the mounts and nothing better than the original brand, my trolling motor is back just like it was new again. Don't settle for initiations just to save maybe two or three dollars get the original brand will save you on the long run and good peace of mind.

BUENA SUJECCION PARA MI MOTOR TROLLER.SOLO QUE POR MI MODELO DE TROLLER TUVE QUE COMPRAR POR APARTE TORNILLOS DE 4" MAS LARGOS PARA LOGRAR LLEGAR A LA ROSCA

It fit properly

Serves their purpose

exactly what i was looking for, and less expensive!

don't work very well and up loosening off to easily so there is a danger of loosing the motor.