ENERWAVEZ-Wave Plus Dimmer Switch - Smart Dimmer with Energy Monitor, Neutral Wire Required, Works with Alexa

Finally an in wall Dimmer switch with built in energy monitoring. These work good for dimming, but could be better. These dim by pressing and holding on the paddle, which can cause issues when it gets dimmed down to the point of being off. Then you can press the on button and the light does not come on, which can be fixed by holding the top of the rocker until it comes on. I know it is being picky and every dimmer that dims with the main rocker is this way. Being an electrician I do get to install a lot of different dimmers and have found this type of dimmer to be a problem for some people. It does work good for myself and I can still give it 5 stars even though I think a separate small rocker along the side is a better option.

I'm not often compelled to write a review, but these are bad. I purchased these companion switches to use with Inovelli dimmers. After spending so much on the dimmers I had hoped to save a few bucks per switch by choosing these to use as the companions. But as the adage goes; when you buy cheap, you buy twice.I have 11 of these companions installed. All of my complaints have to do with the 'up'/'on' action (either the tactile click or the actual control). One or two of them work flawlessly. They click both up and down nicely and they control the dimmer fine. One or two of them have no 'click' action on the up half of the rocker, but they do control the dimmer fine. One or two of them have no 'click' action on the up half of the rocker and they DON'T control the dimmer. And the remainder of them 'click' fine, but won't turn the dimmer on.I had a similar issue with some smart switches which was caused by inserting the wires too far into the body of the switch and impeding the travel of the rocker, but that's not the case with these. The ones that don't click also don't click right out of the box before installation.

Easy install (just like a std switch, but add a neutral). Shows power consumption in real time via my Z-wave hub (Ezlo plus). Does not easily slide between say 10% and 100% in my hub, this could be the hub. at 100% brightness the LEDs have installed flicker, you must drop to 95% or less. When used as a manual switch on the wall it is a bit laggy. I have only had it a week, its OK, but not quite what I was hoping for as a dimmer.Update: Running these for two months now, moved to a new hub, returned the Ezlo (stay away). Still have the annoying light flicker at 100% or less than 25% on the new Hubitat Elevation (C7) hub. Also the switches seem to wait about 2 seconds to start fading out when you press the manual off button, instant off with hub command. Also sometimes when you press the on or off button if you just tap it as you go by, it does not get the on or off signal (like the contacts inside the switch did not quite close -- minor annoyance, but always nagging at you (I do not need to relearn how to turn on a switch at any age). I have installed several FEIT brand WIFI dimmers (trying to stay away from WIFI stuff). They work great, no flicker at all, but I really do not want a lot on WIFI -- Google home has lousy rule capability, hubs are MUCH better about event based actions)

I had to troubleshoot why this product did not function via the rocker panel after a couple of weeks. Tech Support was very responsive and did not hesitate to offer a replacement after a brief troubleshooting session.

Pros:- price is competitive compared to other z-wave switches- they work reliably- being able to measure energy and power is niceCons:- Power readings default to sending at 0.1W. This causes an abundance of messages on the z-wave network, and my poor hub is overwhelmed.- The power readings are configurable, but I haven't been able to configure it with the hubs I have: an Aeotec Z-stick + open-zwave using either Home Assistant or the open-zwave control panel, OR the SmartThings Hub.- I haven't figured out a reliable way to add/remove the switch from the z-wave hub. It is very finicky compared to other ones (eg, Homeseer). I had to do this several times to try different hubs to address the previous points, and I wasted hours in the process.- The feel and look of the switch feels cheaper than alternative z-wave switches (eg, Homeseer).

I bought a pair of these Z-Wave switch with power meter and installed them in February. I use the switch about twice a day - turn it on in the evening (mostly use the button) and turn it off after a few hours (mostly from my smartphone). Last week, after 6 months of use, one of them stopped responding to the button. Now I have to turn on my light through my smartphone or computer, even when I stand next to the switch, really awkward.EDIT: Today is October 19, 2019, 9 month after I placed my order, or 8 month after I installed them, both switch stopped working. They can still be controlled through Z-Wave, but not the mechanical rocker. I will replace them with major brands like GE or Honeywell, they don't have power meters but I hope they would last longer.EDIT 2: After contacted their customer service, I was able to revived the rockers by resetting the breaker (from the house breaker panel).

Excellent product

These z wave switches work for a while (purchased about 48) and randomly they stop responding to pressing on and off. I have two that get rather warm. I would not buy them again. Z wave version is old so compatibility with newer controllers are missing features.Updated: contacted Enerlite and their customer support us horrible, offered to rma 4 switches. Or if 48+ that I've bought since 2017. Sure some may be or if warranty... But wait there's a 3 year warranty! Anyways don't ever buy these Chinese made POS. Quality is poor and service is worse.