Cold Air Intake System: High-Flow Air Filter, Increase Performance & Towing: Compatible with 2020-2025 Jeep: Gladiator, Wrangler, JL, 71-1576

Love this CAI. Quality product and easy to install. The sound is much better than stock with a little more giddy up. MPG seemed to go up also.

I have no mechanical experience changing anything out. I took a chance, and with the help of a few YT instructional vids, I was able to change this out. I am so happy with this install! The directions it came with were ok, but the videos found online helped more. Make sure you have all the right tools. You'll need: Trim removal tool Flathead screwdriver Adjustable wrench Sockets 10mm & 8mm Torx bits: T30, T20 Allen head: 5/32 Adaptors may be needed for the sockets Removing the old air intake was one of the main challenges I encountered. I had virtually no issues with installing the new one. Challenges were (I have a Jeep JL): Removing grill without scratching it on the aftermarket front bumper (I only had about a 3/4 of an inch gap to work with). Removing air intake air temperature sensor while being careful with it. Overall, I am very happy with this. It also makes my Jeep sound way better and a little meaner.

It looks very good good construction, easy to install you feel the difference sounds very nice.

While I didn’t get any perceivable change in mileage (wasn’t expecting any), I did get a great sound and maybe a touch more power at the high end of the RPM range. Install was easy although the instructions could have been better. The air temp sensor fitting is not good though and I get a check engine code once ever 500 miles or so. I push it back in and it clears only to repeat itself again. Edit: Check engine was do to the fan failing (at less than 10k miles). CAI is great and I have had no issues 20k miles later.

Was a very easy install, took about two hours by myself. I’m not super auto inclined but the instructions were clear. I did end up using a YouTube video to remove my 2024 gladiators stock intake. But the instructions to assemble this one was fine. I love the way the stainless steel looks gives it a more aggressive sound for sure.

I installed this today and it took me about an hour. Would have been quicker but I was in and out of the house grabbing tools and coffee. The good... 1. Install is easy if you have the right tools and read the instructions, Youtube videos exist so if you need more direction just google Jeep Gladiator K&N Cold Air Intake Install. 2. The motor growls when you hit the throttle! I do not want the full sound of an aftermarket exhaust but the stock intake makes no sound at all. If you are looking for a nice growl without being obnoxious (IMO) this is the way to go. 3. Throttle response is noticeable better but not sure how much of that is associated with the sound, it could be a Jedi mind trick. 4. This is handmade in the USA!1 (according to the box) The bad... 1. Other brands do not require you take the grill off and remove the air inlet tube behind. This is not a big deal if you are familiar with removing the grill but it still adds time to the overall install. 2. I have had other vehicles with CAIs and sometimes at low rpms they can feel sluggish. Overall they add HP and I believe they are worth it but it is something to keep in mind. I still rate this as 5 stars despite these very small issues.

Update: I’ve had this for two years and it’s only gotten worse. The quality of the plastic is complete garbage. C’mon K&N, do better. Inexcusable for this amount of money. I’m lowering my review to one star, the metal inserts are completely pulling out of the plastic, I’d avoid this until the manufacturer can improve the design. Not hard to install but beware screwing in the air sensor port, cheap plastic on cheap plastic and snap. Would’ve cost the manufacturer another buck or two to do it right or better yet build it into the original mold or pre installed from the factory. I love the product but the design is very sub par.

If you want to save gas and increase power or horsepower get a K&N cold air intake. Very easy to install. The instructions were spot on. If you're not sure there, are you tube videos available.

Inmediatamente después de instalarlo se sienten los caballos extras y por supuesto que el sonido que emite está fregón! 👍🏻

Easy install, looks cool, small hp gain.

I like the performance of the K&N cold air intake thus far. Cannot say it has given much better fuel improvement but it definitely improved the torque and HP, not to mention the low growl that comes out when you accelerate through the gears. The instructions could use a bit of improvement because the tolerances are so close one has to use alternative measures to get the box inserted into the rubber boots under the box itself. Also registering the unit through K&N was seamless, albeit still waiting for a response...Would definitely recommend if you have a Jeep and are running a 3.6l engine.

OMG WHAT A DIFF … mileage has improved I feel the torque diff as well as the HP. And the sound wow it sounds mean deep throated. Great purchase.

It doesn’t have sensor spot i had to make one by my self to fit the sensor in it!!!